rv1108: root: add wifi firmware

Change-Id: I58a17ef13b65f5c49c86d3d7a91ecca9bf4ad902
Signed-off-by: vicent.chi <vicent.chi@rock-chips.com>

rv1108/root/etc/firmware/nvram_ap6181.txt

@@ -0,0 +1,58 @@
+#AP6181_NVRAM_V1.2_05242017
+#adjuest PA parameter for g/n mode
+manfid=0x2d0
+prodid=0x492
+vendid=0x14e4
+devid=0x4343
+boardtype=0x0598
+
+# Board Revision is P307, same nvram file can be used for P304, P305, P306 and P307 as the tssi pa params used are same
+#Please force the automatic RX PER data to the respective board directory if not using P307 board, for e.g. for P305 boards force the data into the following directory /projects/BCM43362/a1_labdata/boardtests/results/sdg_rev0305
+boardrev=0x1307
+boardnum=777
+xtalfreq=26000
+boardflags=0xa00
+sromrev=3
+wl0id=0x431b
+macaddr=00:90:4c:07:71:12
+aa2g=1
+ag0=2
+maxp2ga0=74
+cck2gpo=0x2222
+ofdm2gpo=0x66666666
+mcs2gpo0=0x7777
+mcs2gpo1=0x7777
+pa0maxpwr=56
+
+#P207 PA params
+#pa0b0=5447
+#pa0b1=-658
+#pa0b2=-175<div></div>
+
+#Same PA params for P304,P305, P306, P307
+
+pa0b0=5447
+pa0b1=-607
+pa0b2=-160
+pa0itssit=62
+pa1itssit=62
+
+
+cckPwrOffset=5
+ccode=0
+rssismf2g=0xa
+rssismc2g=0x3
+rssisav2g=0x7
+triso2g=0
+noise_cal_enable_2g=0
+noise_cal_po_2g=0
+swctrlmap_2g=0x04040404,0x02020202,0x02020202,0x010101,0x1ff
+temp_add=29767
+temp_mult=425
+temp_q=10
+initxidx2g=45
+tssitime=1
+rfreg033=0x19
+rfreg033_cck=0x1f
+cckPwrIdxCorr=-8
+spuravoid_enable2g=1

rv1108/root/etc/firmware/nvram_ap6212a.txt

@@ -0,0 +1,55 @@
+#AP6212A_NVRAM_V1.0.1_20160606
+# 2.4 GHz, 20 MHz BW mode
+
+# The following parameter values are just placeholders, need to be updated.
+manfid=0x2d0
+prodid=0x0726
+vendid=0x14e4
+devid=0x43e2
+boardtype=0x0726
+boardrev=0x1101
+boardnum=22
+macaddr=00:90:4c:c5:12:38
+sromrev=11
+boardflags=0x00404201
+xtalfreq=26000
+nocrc=1
+ag0=255
+aa2g=1
+ccode=ALL
+
+pa0itssit=0x20
+extpagain2g=0
+
+#PA parameters for 2.4GHz, measured at CHIP OUTPUT
+pa2ga0=-215,5267,-656
+AvVmid_c0=0x0,0xc8
+cckpwroffset0=5
+
+# PPR params
+maxp2ga0=80
+txpwrbckof=6
+cckbw202gpo=0x6666
+legofdmbw202gpo=0xaaaaaaaa
+mcsbw202gpo=0xbbbbbbbb
+
+# OFDM IIR :
+ofdmdigfilttype=18
+ofdmdigfilttypebe=18
+# PAPD mode:
+papdmode=2
+
+il0macaddr=00:90:4c:c5:12:38
+wl0id=0x431b
+
+#OOB parameters
+hostwake=0x40
+hostrdy=0x41
+usbrdy=0x03
+usbrdydelay=100
+deadman_to=0xffffffff
+# muxenab: 0x1 for UART enable, 0x10 for Host awake
+muxenab=0x10
+# CLDO PWM voltage settings - 0x4 - 1.1 volt
+#cldo_pwm=0x4
+glitch_based_crsmin=1

rv1108/root/etc/firmware/nvram_ap6236.txt

@@ -0,0 +1,66 @@
+#AP6236_NVRAM_V1.1.1_20180815
+# NVRAM file for BCM943430WLPTH, Bx Chip
+# 2.4 GHz, 20 MHz BW mode
+
+# The following parameter values are just placeholders, need to be updated.
+manfid=0x2d0
+prodid=0x0727
+vendid=0x14e4
+devid=0x43e2
+boardtype=0x0727
+boardrev=0x1331
+boardnum=22
+macaddr=00:90:4c:c5:12:38
+sromrev=11
+boardflags=0x00404201
+boardflags3=0x08000000
+xtalfreq=26000
+nocrc=1
+ag0=255
+aa2g=1
+ccode=ALL
+
+pa0itssit=0x20
+extpagain2g=0
+#PA parameters for 2.4GHz, measured at CHIP OUTPUT
+pa2ga0=-202,5582,-671
+AvVmid_c0=0x0,0xc8
+cckpwroffset0=5
+
+# PPR params
+maxp2ga0=74
+txpwrbckof=6
+cckbw202gpo=0x2222
+legofdmbw202gpo=0x55555555
+mcsbw202gpo=0x76666666
+propbw202gpo=0xcc
+
+# OFDM IIR :
+ofdmdigfilttype=18
+ofdmdigfilttypebe=18
+# PAPD mode:
+papdmode=1
+pacalidx2g=42
+papdepsoffset=-22
+papdendidx=58
+
+# LTECX flags
+ltecxmux=0
+ltecxpadnum=0x0102
+ltecxfnsel=0x44
+ltecxgcigpio=0x01
+
+il0macaddr=00:90:4c:c5:12:38
+wl0id=0x431b
+
+deadman_to=0xffffffff
+# muxenab: 0x1 for UART enable, 0x2 for GPIOs, 0x8 for JTAG
+muxenab=0x10
+# CLDO PWM voltage settings - 0x4 - 1.1 volt
+#cldo_pwm=0x4
+
+#VCO freq 326.4MHz
+spurconfig=0x3 
+
+AvVmidIQcal=0x2,0xa8
+glitch_based_crsmin=1