824f3ac23c
-e4ccbc, surport cv1810c arm32. -921783, add sensor ov_os02n10_1l. -8b96e4, support 180zb uboot spl. -937493, Sync spacc config. -3e99d9, add phy config for cv180x. -333b4d, fixed the dts file of cv1812cpa. Change-Id: I86ce96f27d890af09a2b26d2cc955936bbc35903
61 lines
2.7 KiB
Makefile
61 lines
2.7 KiB
Makefile
opensbi: export CROSS_COMPILE=$(CONFIG_CROSS_COMPILE_SDK)
|
|
opensbi: u-boot-build
|
|
$(call print_target)
|
|
${Q}$(MAKE) -j${NPROC} -C ${OPENSBI_PATH} PLATFORM=generic \
|
|
FW_PAYLOAD_PATH=${UBOOT_PATH}/${UBOOT_OUTPUT_FOLDER}/u-boot-raw.bin \
|
|
FW_FDT_PATH=${UBOOT_PATH}/${UBOOT_OUTPUT_FOLDER}/arch/riscv/dts/${CHIP}_${BOARD}.dtb
|
|
|
|
opensbi-clean:
|
|
$(call print_target)
|
|
${Q}$(MAKE) -C ${OPENSBI_PATH} PLATFORM=generic distclean
|
|
|
|
FSBL_OUTPUT_PATH = ${FSBL_PATH}/build/${PROJECT_FULLNAME}
|
|
ifeq ($(call qstrip,${CONFIG_ARCH}),riscv)
|
|
fsbl-build: opensbi
|
|
endif
|
|
ifeq (${CONFIG_ENABLE_FREERTOS},y)
|
|
fsbl-build: rtos
|
|
fsbl%: export BLCP_2ND_PATH=${FREERTOS_PATH}/cvitek/install/bin/cvirtos.bin
|
|
fsbl%: export RTOS_DUMP_PRINT_ENABLE=$(CONFIG_ENABLE_RTOS_DUMP_PRINT)
|
|
fsbl%: export RTOS_DUMP_PRINT_SZ_IDX=$(CONFIG_DUMP_PRINT_SZ_IDX)
|
|
fsbl%: export RTOS_FAST_IMAGE_TYPE=${CONFIG_FAST_IMAGE_TYPE}
|
|
fsbl%: export RTOS_ENABLE_FREERTOS=${CONFIG_ENABLE_FREERTOS}
|
|
endif
|
|
fsbl%: export FSBL_SECURE_BOOT_SUPPORT=${CONFIG_FSBL_SECURE_BOOT_SUPPORT}
|
|
fsbl%: export ARCH=$(call qstrip,${CONFIG_ARCH})
|
|
fsbl%: export OD_CLK_SEL=${CONFIG_OD_CLK_SEL}
|
|
fsbl%: export VC_CLK_OVERDRIVE=${CONFIG_VC_CLK_OVERDRIVE}
|
|
fsbl%: export KERNEL_SUSPEND=${CONFIG_KERNEL_SUSPEND}
|
|
fsbl%: export TPU_PERF_MODE=$(shell if [ "${CONFIG_CHIP_cv1812cp}" = "y" ] || [ "${CONFIG_CHIP_sg2002}" = "y" ]; then echo "y";else echo "n";fi)
|
|
fsbl-build: u-boot-build memory-map
|
|
$(call print_target)
|
|
${Q}mkdir -p ${FSBL_PATH}/build
|
|
${Q}ln -snrf -t ${FSBL_PATH}/build ${CVI_BOARD_MEMMAP_H_PATH}
|
|
${Q}$(MAKE) -j${NPROC} -C ${FSBL_PATH} O=${FSBL_OUTPUT_PATH} BLCP_2ND_PATH=${BLCP_2ND_PATH} \
|
|
LOADER_2ND_PATH=${UBOOT_PATH}/${UBOOT_OUTPUT_FOLDER}/u-boot-raw.bin
|
|
${Q}cp ${FSBL_OUTPUT_PATH}/fip.bin ${OUTPUT_DIR}/
|
|
ifeq (${CONFIG_UBOOT_SPL_CUSTOM},y)
|
|
${Q}$(MAKE) -C ${FSBL_PATH} clean O=${FSBL_OUTPUT_PATH}
|
|
${Q}$(MAKE) -j${NPROC} -C ${FSBL_PATH} O=${FSBL_OUTPUT_PATH} BLCP_2ND_PATH=${BLCP_2ND_PATH} \
|
|
CONFIG_SKIP_UBOOT=$(CONFIG_SKIP_UBOOT) LOADER_2ND_PATH=${UBOOT_PATH}/${UBOOT_OUTPUT_FOLDER}/spl/u-boot-spl-raw.bin
|
|
${Q}cp ${FSBL_OUTPUT_PATH}/fip.bin ${OUTPUT_DIR}/fip_spl.bin
|
|
else
|
|
${Q}cp ${FSBL_OUTPUT_PATH}/fip.bin ${OUTPUT_DIR}/fip_spl.bin
|
|
endif
|
|
|
|
fsbl-clean: rtos-clean
|
|
$(call print_target)
|
|
${Q}$(MAKE) -C ${FSBL_PATH} clean O=${FSBL_OUTPUT_PATH}
|
|
|
|
u-boot-dep: fsbl-build ${OUTPUT_DIR}/elf
|
|
$(call print_target)
|
|
ifeq ($(call qstrip,${CONFIG_ARCH}),riscv)
|
|
${Q}cp ${OPENSBI_PATH}/build/platform/generic/firmware/fw_payload.bin ${OUTPUT_DIR}/fw_payload_uboot.bin
|
|
${Q}cp ${OPENSBI_PATH}/build/platform/generic/firmware/fw_payload.elf ${OUTPUT_DIR}/elf/fw_payload_uboot.elf
|
|
endif
|
|
|
|
ifeq ($(call qstrip,${CONFIG_ARCH}),riscv)
|
|
u-boot-clean: opensbi-clean
|
|
endif
|
|
u-boot-clean: fsbl-clean
|